做好電動卷簾門的維修和保養，可以延長它的使用時間，提升使用的性能，不僅是在操作的過程，日常維護對濟南電動卷簾門也有很重要的作用，接下來，我們就來了解一下它的維修保養方法，希望以下內容對您有所幫助。

Do a good job in the repair and maintenance of electric roller shutter door, can extend its use time, improve the performance of use, not only in the process of operation, daily maintenance of Jinan electric roller shutter door also has a very important role, next, we'll learn about its repair and maintenance methods, hope the following can help you.

電動卷簾門維修保養的辦法：

Maintenance methods of electric rolling shutter door:

操作電動卷簾門時，操作者站在能看到卷門運轉形態的地位停止操作，否則易發作不測而受損。

When operating the electric rolling shutter door, the operator should stop the operation at the position where he can see the rolling shutter operation mode, otherwise it is easy to be damaged.

濟南電動卷簾門門簾和卷門機制止與酸、堿性物溶液接觸，以防腐蝕門簾外表。   卷門機在運轉、滑行、傳動等部位應活期反省(多每年2次.，并依據需求及時加油，以保證卷簾門的正常運用。

Jinan electric roller shutter door curtain and roller shutter mechanism to prevent contact with acid, alkaline solution, in order to prevent corrosion curtain appearance. The operation, sliding, transmission and other parts of the rolling door machine should be introspected regularly (at most twice a year), and timely refueled according to the demand, so as to ensure the normal operation of the rolling door.

卷簾門門簾和易銹部位，應停止活期防腐、油漆及頤養處置，制止用重物、硬物沖擊門面。

The current anti-corrosion, painting and self-care treatment shall be stopped for the rolling door curtain and the parts easy to rust, and the heavy objects and hard objects shall not be used to impact the door surface.

卷簾門運轉時如有發作較大顫動或異常聲響時應停機反省，掃除有礙門簾正常啟閉的雜物。

When the rolling shutter door is running, if there is a big vibration or abnormal sound, it should stop and reflect, and sweep away the sundries that hinder the normal opening and closing of the curtain.

濟南電動卷簾門底梁座下限地位與軸承架下端堅持大于200mm的間隔，以確保制動中止時不發作沖頂景象。

Jinan electric roller shutter door bottom beam seat lower position and the lower end of the bearing frame adhere to more than 200 mm interval, to ensure that the braking stop does not occur when the top rush scene.

電動卷簾門5

Electric rolling shutter 5

卷簾門裝置地位的上端應有牢靠的防火設備，在卷簾門的卷筒下端做包箱或吊頂時設置可拆式活動蓋板，在電動卷門機一側下端預留500×500mm可拆檢修孔，以便于維修頤養。

The upper end of the roller shutter device shall be equipped with reliable fire prevention equipment. When the box or ceiling is made at the lower end of the roller shutter, removable movable cover plate shall be set. 500 × 500mm removable manhole shall be reserved at the lower end of one side of the electric roller shutter to facilitate maintenance.

一切電動控制的卷簾門，啟閉運轉方向與開關箱指示相反，特別是在新接通電源試車或外來輸出電源變換相線時，應先運用手動安裝將門簾置于門洞高度1/2 的地位，接通電源后試操作卷門啟閉，直到與指示相附，方可正常運用，否則損壞限位器，惹起卷簾反卷或沖頂等而形成損失。

For all electrically controlled rolling shutter doors, the opening and closing direction is opposite to that indicated by the switch box, especially when the new power supply is connected for test run or the external output power supply is used to change the phase line, the manual installation shall be used first, and the curtain shall be placed at 1 / 2 of the door opening height After the power is turned on, try to open and close the rolling door until it is attached with the indication. Otherwise, the limiter will be damaged, and the rolling shutter will roll back or rush to the top.

電動卷簾門在啟閉中止進程中，應具有隨位中止之功用，不應有中止而持續下滑景象，如發作下滑間隔大于50mm的狀況呈現，應立刻對卷簾門控制電器和卷門機制動器停止細心反省修繕，運轉正常為止。

In the process of stopping the opening and closing of the electric rolling shutter door, it should have the function of stopping with the position. There should be no scene of continuous sliding due to the stopping. If the sliding interval is more than 50 mm, the rolling shutter door control appliance and rolling door mechanism actuator should be carefully repaired immediately until the normal operation.

濟南電動卷簾門在日常生活中，能夠為人們提供很大的便利，做好保養維修可以讓他更好的為人們服務，運行是否正常，門簾易生銹部位做好防腐和清潔處理，保證運行，以免在使用過程中出現停滯或者影響使用的情況，關于維修保養的事項，大家可以參考文中講到的方法做為參考。

Jinan electric roller shutter door in daily life, can provide great convenience for people, good maintenance can let him better service for people, whether the operation is normal, easy to rust parts of the curtain do anti-corrosion and cleaning treatment, ensure the operation, in order to avoid stagnation or affect the use of the situation in the process of use, about maintenance matters, you can refer to the text The method to be used as a reference.