With the acceleration of the pace of life, people have higher requirements for all aspects. With the continuous progress of life, electric roller shutter doors will be used in many places of life, which can help people improve work efficiency and save time. So, roller shutter door is widely used, do you know its installation method, do you know its related use matters, next, Jinan electric roller shutter door for you to do related explanation.

無論是電動卷簾門，還是卷簾門，只要掌握了正確的安裝方法，在安裝的時候將會變得更加容易，你也不用為了如何安裝電動卷簾門而煩惱了。

Whether it's electric rolling shutter door or rolling shutter door, as long as you master the correct installation method, it will be easier to install, and you don't have to worry about how to install electric rolling shutter door.

濟南電動卷簾門的安裝方法：

Installation method of Jinan electric rolling shutter door:

先預留出PVC管道，從控制盒的位置下端往下地平面以下，穿墻往外，軌道大致位置地平面下一定的距離，供以后伸縮門電動卷簾門室外線路入室接著安裝電動卷簾門，接好線路，調試開關控制盒。

The PVC pipe is reserved first, from the lower end of the control box to below the ground level, through the wall to the outside, to a certain distance under the ground level of the approximate position of the track, for the outdoor line of the electric rolling shutter door of the telescopic door to enter the room, then the electric rolling shutter door is installed, the line is connected, and the switch control box is debugged.

之后調出門洞長度，有條件的可將門洞總長度再加長一定的長度，這樣可將檢修孔改成一扇小門，方便日后檢修維護伸縮門電氣線路。

After that, the length of the door opening can be adjusted, and the length of the hole can be lengthened by a certain length, so that the repair hole can be turned into a small door, which is convenient for maintenance and maintenance of the telescopic door electrical circuit in the future.

再將電源引到控制盒的位置下端，需要有漏電保護裝置，并采用PVC暗敷。在進行確定傳達室內控制盒的位置，即操縱電動卷簾門開關的裝置位置。

Then, the power supply is led to the lower end of the control box, and the leakage protection device is required, and PVC is used for concealed laying. The position of the control box in the transmission room is determined, that is, the position of the device that operates the switch of the electric rolling shutter door.

安裝后，在鋪設軌道的同時，土建配合做好軌道處的地面，注意鋪設軌道期間，路面禁止通行，以免壓彎軌道。

After installation, while laying the track, the civil engineering shall cooperate with the ground of the track. During the laying of the track, the road shall be forbidden to pass to avoid bending the track.

安裝完成后，需要對質量進行檢測，那么，電動卷簾門該如何檢測質量呢?

After the installation, the quality needs to be tested, so how to test the quality of the electric rolling shutter door?

由于電動卷門是由電機來控制門簾的上升和下降的，所以需要檢查看電動卷門在上升和下降的時候是否有個緩沖的過程，這個是衡量電動卷門品質的一個重要的指標。如果沒有緩沖裝置的話，那樣就很有可能發生事故。電動卷門防止撞擊軌道，防止夾人這個標志是衡量電動卷門品質的好與壞的重要的因數。

As the electric rolling door is controlled by the motor to rise and fall the curtain, it is necessary to check whether there is a buffer process when the electric rolling door rises and falls, which is an important index to measure the quality of the electric rolling door. If there is no buffer device, then it is very likely to have an accident. The sign of preventing the electric rolling door from hitting the track and clamping is an important factor to measure the quality of the electric rolling door.

正確的安裝方法是實用電動卷簾門的前提，安裝完成后需要對卷簾門進行質量的檢測，相信以上講述對您了解電動卷簾門有了幫助，如果您想了解更多關于濟南電動卷簾門的信息，請查閱我們的網站。

The correct installation method is the premise of practical electric roller shutter door. After the installation, the quality of the roller shutter door needs to be tested. I believe the above description is helpful for you to understand the electric roller shutter door. If you want to know more about Jinan electric roller shutter door, please refer to our website.