濟南卷簾門成為很多家庭使用的門，伸縮方便，節省空間，應用范圍非常廣。而且卷簾門的種類也越來越多了，那么卷簾門怎么安裝呢?在本文中就為大家介紹幾種常見的卷簾門安裝步驟。

Jinan roller shutter door has become a door used by many families. It is easy to expand and retract, saves space, and has a wide range of applications. And there are more and more kinds of roller shutter doors. How to install roller shutter doors? In this article, we will introduce several common installation steps of roller shutter door.

電動卷簾門安裝步驟：

Installation steps of electric roller shutter door:

1、先在需要安裝的門框框口位置畫出線。表明尺寸大小，然后找工作人員設計出合適的電動卷簾門，這里值得注意的一點是框內高度比門扇的高度要高一點點。

1. Draw the line at the door frame opening to be installed. Indicate the size, and then find the staff to design a suitable electric roller shutter door. What is worth noting here is that the height of the frame is a little higher than the height of the door leaf.

2、先把電動卷簾門的門框固定，這里要先拆掉門框下部的固定板。

2. First fix the door frame of the electric roller shutter door. Here, remove the fixing plate at the lower part of the door frame.

3、安裝電動卷簾門扇主體門扇。一定要保證電動卷簾門與墻體結成整體，封閉性要做好，再粉刷洞口及墻體。粉刷完畢后，門縫應均勻平整，開啟電動卷簾門應該自由輕便，不得有過緊、過松和反彈現象。

3. Install the main door leaf of the electric roller shutter door leaf. Make sure that the electric roller shutter door and the wall form a whole, and the sealing shall be done well, and then paint the opening and the wall. After painting, the door seam shall be even and flat. The electric roller shutter door shall be free and light to open, and shall not be too tight, too loose or rebound.

防火卷簾門安裝步驟：

Installation steps of fireproof rolling shutter door:

1、按設計型號，查閱產品說明書和電氣原理圖。

1. Refer to the product manual and electrical schematic diagram according to the design model.

2、測量洞口標高，彈出兩導軌垂線及卷筒線。

2. Measure the elevation of the hole, and snap the vertical lines of the two guide rails and the center line of the drum.

3、將墊板電焊在預埋鐵板上，用螺絲固定卷筒的左右支架，安裝卷筒。卷筒安裝后應轉動靈活。

3. Weld the backing plate on the embedded iron plate, fix the left and right supports of the drum with screws, and install the drum. The drum shall rotate flexibly after installation.

4、安裝減速器和傳動系統。

4. Install the reducer and drive system.

5、安裳電氣拴街系統。

5. Anshang electric street system.

6、空載試車。

6. No load test run.

7、將事先裝配好的簾板安裝在卷筒上。

7. Install the curtain plate assembled in advance on the drum.

8、安裝導軌。按圖紙規定位置，將兩側及上方導軌焊牢于墻體預埋件上，并焊成以體，各導軌應在同一垂直平面上。

8. Install the guide rail. According to the positions specified in the drawings, the guide rails on both sides and above shall be welded to the embedded parts of the wall and welded into a body. Each guide rail shall be on the same vertical plane.

9、安裝水幕噴淋系統，并與總控制系統連接。

9. Install the water curtain spraying system and connect it with the general control system.

10、試車。先用手去試運行，再用電動機啟閉數次，調整無卡住、阻滯及異常。

10. Test run. Test run by hand first, and then open and close the motor for several times until there is no jam, block and abnormality.

自動門水晶卷簾門安裝步驟：

Installation steps of automatic door crystal roller shutter:

1、先看手動鏈條是否向下，在將電機固定在主板上，在把鏈條固定在輪盤和電機底座齒輪連接(一定上緊)在將遙控接線盒與電機連接，試下手柄是否顛倒，如顛倒遙控接收盒側方有黑色按鍵，向另一方撥動助即可。

1. First, check whether the manual chain is down. After fixing the motor on the main board, after fixing the chain on the wheel plate and connecting the motor base gear (tighten it), and after connecting the remote control junction box with the motor, try whether the handle is reversed. If there is a black button on the side of the reverse remote control receiving box, just move it to the other side.

2、用尺子量主板和副板的外邊看下尺寸是否正確，如正確把軸上在側板上，注意要先把軸打一條水平線，再用10個鉆頭打孔50公分，1個一定要直，再用14的鏍母焊在軸上，記住要與軸上的孔垂直在焊，一定要焊牢固，再把簾子的片的與軸上的孔對齊用10個的鉆頭打孔一定要垂直(也可以用快絲固定)。

2. Use a ruler to measure the outer edges of the main board and the auxiliary board to see if the dimensions are correct. If the shaft is correctly placed on the side plate, pay attention to striking a horizontal line on the shaft first, then drill 50 cm with 10 drills, and one must be straight. Then weld the shaft with 14 screws. Remember to weld vertically with the hole on the shaft, and be sure to weld firmly, Then align the center of the first piece of the curtain with the hole on the shaft, and use 10 drill bits to drill holes, which must be vertical (or fixed with fast wire).

3、在將卷簾門簾片穿好兩側用封頭封好用拉鉚釘拉住(記住開始封各一片封一個)。

3. Seal the two sides of the rolling shutter door curtain with heads and pull them with rivets (remember to seal one piece at the beginning).

4、封完后用繩翻過軸把簾子打個孔一頭一個用繩拴住，別一端用人拽住，按下手柄的上升鍵，使軸運行將簾子帶上去，鏍絲桿把簾子和軸連在一起(水平要擰緊加墊)再把簾子升上去，一定要牢固。

4. After sealing, use a rope to turn over the shaft to make a hole for the curtain, one end of which is tied with a rope, and the other end is held by a person. Press the up button of the handle to make the shaft run to bring the curtain up. The screw rod connects the curtain and the shaft together (the horizontal screw should be tightened and padded), and then the curtain should be lifted up firmly.

5、把軌道的一端開成人字口。

5. Open one end of the track into a slot.

6、把卷簾門簾子調平，上下線定位，左邊滑輪是上限位，右邊是下限位，(根據現場需要自行調節)。

6. Level the curtain of the roller shutter door, and position the upper and lower lines. The left pulley is the upper limit and the right pulley is the lower limit. (adjust it according to the needs of the site).

以上就是關于“幾種常見的卷簾門安裝步驟”的全部內容，希望能對大家有所幫助。還有更多類型的卷簾門內容值得了解，來我們網站http://www.wurkt.com咨詢更多吧！

The above is all about the "installation steps of several common rolling shutter doors". I hope it can help you. There are more types of roller shutter doors worth knowing. Come to our website http://www.wurkt.com Ask more!